Draft Roadmap

Test proposal

The following document describes the test cases which must meet the following objectives:

• Ensuring the hardware meets the required performance for substation grade protection regarding latency, jitter, interoperability and reliability
• Ensuring the software platform meets the required performance for substation grade protection regarding latency, jitter, interoperability and reliability
• Provide system characteristics/benchmarks
• Provide indications on scalability

seapath.pptx

Documentation

The documentation is available directly on github.

Here is the main documentation to build a SEAPATH image: https://github.com/seapath/yocto-bsp/blob/master/README.adoc

Build machine

The Yocto project requires a powerful Linux based machine.

In order to build efficiently the SEAPATH project, we recommend not to use Virtual Machine. The Yocto project will ensure to multi-thread your build, so try to use a build machine with many CPU cores.

Here is a discussion on the Yocto Project mailing list: https://lists.yoctoproject.org/g/yocto/topic/72047879#48815

Here is for instance, a build configuration (~1500 euros) used:

Tips for building

• About 250GB is needed for building SEAPATH.
• A USB attached storage may be too slow to be practical for a successful build.
• Ensure you use an ext 2/ ext3 / ext4 filesystem for the build directory. NTFS will not work.
• Watch out with only manually deleting the /tmp/work directory. Instead delete the whole tmp directory.
• When deleting the tmp, it may take a very long time, and might cause rm -rf to fail with an error. find . -delete will work better, as it will not try to index all files before deleting them.

Test Bench/Reference hardware

This is the reference hardware for the Seapath project and supported out of the box. It might cost significant time to support other hardware (e.g. AMD processors). Some integration is available with a dedicated Yocto layer: https://git.yoctoproject.org/cgit/cgit.cgi/meta-amd/

Specification

Tests results

Real time

Tests

With the previous test bench hardware, a couple of tests were used.

We used cyclictest:

"Cyclictest accurately and repeatedly measures the difference between a thread's intended wake-up time and the time at which it actually wakes up in order to provide statistics about the system's latencies. It can measure latencies in real-time systems caused by the hardware, the firmware, and the operating system." (source: https://wiki.linuxfoundation.org/realtime/documentation/howto/tools/cyclictest/start).

The following arguments were provided:

cyclictest -l100000000 -m -Sp90 -i200 -h400 -q >output

This test is very long (~5 hours).

You can then plot the latency graph:

./yocto-bsp/tools/gen_cyclic_test.sh -i output -n 28 -o output.png

• output is the output file generated by cyclictest
• 28 match the amount of CPU used.
• output.png is the latency graph file.

Note:

1. we used the same arguments than used by OSADL (https://www.osadl.org/Latency-plots.latency-plots.0.html)
2. We  created a script to plot the latency graph as done by OSADL

Results

Hypervisors

• With Kernel RT Full Preempt (CONFIG_PREEMPT_RT_FULL=y)

• Without Kernel RT Full Preempt (CONFIG_PREEMPT_NONE=y)

Virtual machines

All  Yocto images include the ability to run guest Virtual Machines (VMs).

We used KVM and Qemu to run them. As we do not have any window manager on the host system,
VMs should be launched in console mode and their console output must be correctly set.

For testing purpose, we can run our Yocto image as a guest machine.
We do not use the .wic image which includes the Linux Kernel and the rootfs because
we need to set the console output.
We use two distinct files to modify the Linux Kernel command line:

- bzImage: the Linux Kernel image
- seapath-test-image-votp.ext4: the rte rootfs

Then run:

qemu-system-x86_64 -accel kvm -kernel bzImage -m 4096 -hda seapath-test-image-votp.ext4 -nographic -append 'root=/dev/sda console=ttyS0'

Docker

You can use docker check-config.sh to check that all necessary configurations of the host linux Kernel are set:

info: reading kernel config from /proc/config.gz ...

Generally Necessary:
- cgroup hierarchy: properly mounted [/sys/fs/cgroup]
- CONFIG_NAMESPACES: enabled
- CONFIG_NET_NS: enabled
- CONFIG_PID_NS: enabled
- CONFIG_IPC_NS: enabled
- CONFIG_UTS_NS: enabled
- CONFIG_CGROUPS: enabled
- CONFIG_CGROUP_CPUACCT: enabled
- CONFIG_CGROUP_DEVICE: enabled
- CONFIG_CGROUP_FREEZER: enabled
- CONFIG_CGROUP_SCHED: enabled
- CONFIG_CPUSETS: enabled
- CONFIG_MEMCG: enabled
- CONFIG_KEYS: enabled
- CONFIG_VETH: enabled
- CONFIG_BRIDGE: enabled
- CONFIG_BRIDGE_NETFILTER: enabled
- CONFIG_NF_NAT_IPV4: enabled
- CONFIG_IP_NF_FILTER: enabled
- CONFIG_IP_NF_TARGET_MASQUERADE: enabled
- CONFIG_NETFILTER_XT_MATCH_ADDRTYPE: enabled
- CONFIG_NETFILTER_XT_MATCH_CONNTRACK: enabled
- CONFIG_NETFILTER_XT_MATCH_IPVS: enabled
- CONFIG_IP_NF_NAT: enabled
- CONFIG_NF_NAT: enabled
- CONFIG_NF_NAT_NEEDED: enabled
- CONFIG_POSIX_MQUEUE: enabled

Optional Features:
- CONFIG_USER_NS: enabled
- CONFIG_SECCOMP: enabled
- CONFIG_CGROUP_PIDS: enabled
- CONFIG_MEMCG_SWAP: enabled
- CONFIG_MEMCG_SWAP_ENABLED: enabled
    (cgroup swap accounting is currently enabled)
- CONFIG_LEGACY_VSYSCALL_EMULATE: enabled
- CONFIG_BLK_CGROUP: enabled
- CONFIG_BLK_DEV_THROTTLING: enabled
- CONFIG_IOSCHED_CFQ: enabled
- CONFIG_CFQ_GROUP_IOSCHED: enabled
- CONFIG_CGROUP_PERF: enabled
- CONFIG_CGROUP_HUGETLB: enabled
- CONFIG_NET_CLS_CGROUP: enabled
- CONFIG_CGROUP_NET_PRIO: enabled
- CONFIG_CFS_BANDWIDTH: enabled
- CONFIG_FAIR_GROUP_SCHED: enabled
- CONFIG_RT_GROUP_SCHED: missing
- CONFIG_IP_NF_TARGET_REDIRECT: enabled
- CONFIG_IP_VS: enabled
- CONFIG_IP_VS_NFCT: enabled
- CONFIG_IP_VS_PROTO_TCP: enabled
- CONFIG_IP_VS_PROTO_UDP: enabled
- CONFIG_IP_VS_RR: enabled
- CONFIG_EXT4_FS: enabled
- CONFIG_EXT4_FS_POSIX_ACL: enabled
- CONFIG_EXT4_FS_SECURITY: enabled
- Network Drivers:
  - "overlay":
    - CONFIG_VXLAN: enabled
      Optional (for encrypted networks):
      - CONFIG_CRYPTO: enabled
      - CONFIG_CRYPTO_AEAD: enabled
      - CONFIG_CRYPTO_GCM: missing
      - CONFIG_CRYPTO_SEQIV: missing
      - CONFIG_CRYPTO_GHASH: missing
      - CONFIG_XFRM: enabled
      - CONFIG_XFRM_USER: enabled
      - CONFIG_XFRM_ALGO: enabled
      - CONFIG_INET_ESP: missing
      - CONFIG_INET_XFRM_MODE_TRANSPORT: missing
  - "ipvlan":
    - CONFIG_IPVLAN: enabled
  - "macvlan":
    - CONFIG_MACVLAN: enabled
    - CONFIG_DUMMY: missing
  - "ftp,tftp client in container":
    - CONFIG_NF_NAT_FTP: enabled
    - CONFIG_NF_CONNTRACK_FTP: enabled
    - CONFIG_NF_NAT_TFTP: missing
    - CONFIG_NF_CONNTRACK_TFTP: missing
- Storage Drivers:
  - "aufs":
    - CONFIG_AUFS_FS: missing
  - "btrfs":
    - CONFIG_BTRFS_FS: missing
    - CONFIG_BTRFS_FS_POSIX_ACL: missing
  - "devicemapper":
    - CONFIG_BLK_DEV_DM: enabled
    - CONFIG_DM_THIN_PROVISIONING: missing
  - "overlay":
    - CONFIG_OVERLAY_FS: missing
  - "zfs":
    - /dev/zfs: missing
    - zfs command: missing
    - zpool command: missing

Limits:
- /proc/sys/kernel/keys/root_maxkeys: 1000000

Contribution process

• Create a personal fork of the project on Github
• Clone the fork on your local machine
• Make sure to pull upstream changes into your local repository
• Implement/fix your feature, comment your code if needed
• Follow the code style of the project, including indentation
• Run tests on the hardware you want to install the distribution and ensure that no regression are seen (ex: cukinia)
• Provide the hardware specification
• Write or adapt tests as needed
• Add or change the documentation as needed.
• Squash intermediary commits (fixes, WIP, …) with git's interactive rebase. 
• Make sure to split your commit
• Each commit should only add one feature
• Use two separate commits when adding a package and enabling it
• Make sure that your commit message is consistent with the git history
• Prefix the commit title by the area touch 
• ex: images/seapath-host-common.inc: add STONITH plugins
• Separate subject from body with a blank line
• Limit the subject line to 50 characters
• Use the imperative mood in the subject line
• Wrap the body at 72 characters
• Use the body to explain what and why vs. how

More details can be found there.

• Sign off your commit

• Push your branch to your fork on Github
• From your fork open a pull request

Code of conduct

the code of conduct is available here